What is the difference between a bespoke wardrobe and a standard one?

A bespoke wardrobe is designed for the specific opening (height, width, wall plumb), which removes the ugly side gaps and uses the full height up to the ceiling. A standard one is cheaper but leaves gaps on the sides and top.

Can carpentry be done without a general renovation?

Yes. Doors, built-in wardrobes and bespoke furniture can be installed as a standalone intervention, with protection of the rest of the home and a usual timeline of 2–4 weeks from the measuring visit.

Interior, exterior and furniture

Bespoke carpentry for homes in Málaga

Bespoke carpentry solves doors, built-in wardrobes, timber wall cladding and integrated furniture that an off-the-shelf product cannot cover. We work with solid timber, lacquered MDF and high-resistance melamine boards.

Request a quote arrow_forward call 678 716 645

What it involves

Millimetric precision and the right hardware

Interior carpentry resolves passage doors, built-in wardrobes, walk-in closets, integrated shelving, wall cladding and bathroom or living-room furniture that fits exactly into the available opening. Exterior carpentry focuses on entrance doors, timber joinery for traditional homes and porches.

Material determines cost and behaviour. Solid timber (oak, beech, treated pine) is more stable and restorable; lacquered MDF allows perfect finishes at a controlled cost; high-resistance melamine is the standard for wardrobe interiors and non-visible areas.

Applications

Three typical contexts for bespoke carpentry

Bespoke carpentry solves what off-the-shelf cannot: using every centimetre of the available opening, absorbing deviations in old walls and delivering personalised finishes. These are the three most demanded contexts.

inventory_2

Wardrobes and walk-ins

Built-in wardrobes fitted to the opening with modular interior (drawers, rails, baskets, shoe racks). Full walk-ins in the main bedroom with direct access to the bathroom.

door_front

Passage and entrance doors

Interior doors in lacquered MDF or natural veneer with concealed or visible frame, and entrance doors in solid timber with security hardware.

chair_alt

Integrated furniture

Bookcases with work area, hallway benches, clad headboards, bathroom furniture with integrated basin and living-room pieces fitted to the available wall.

Measure and make

From the site tape measure to the workshop

Each piece of carpentry starts with on-site measurements, continues at the workshop as a numbered element and finishes with an installation that respects the millimetre.

Typical scope

What this service includes

We resolve carpentry that is part of a renovation and carpentry delivered as a standalone intervention.

door_front

Passage doors

Interior doors with concealed or visible frame, edged and lacquered on site, with quality hardware and a rubber seal to prevent slamming.

inventory_2

Built-in wardrobes and walk-ins

Wardrobes fitted to the available opening, with modular interior (drawers, baskets, rails, shoe racks) adapted to the intended use.

chair

Integrated furniture

Living-room, bathroom or bedroom furniture designed to the dimensions of the space: shelving, benches, headboards and work areas.

dining

Timber cladding

Slatted drop ceilings, wall cladding in natural timber or lacquered slats, and continuous skirting.

home

Traditional exterior joinery

Entrance doors, gates and timber windows for the restoration of traditional homes where aluminium replacement is not appropriate.

straighten

Plumb-line measurements

On-site measurements taken at several points to absorb wall deviations, so the unit fits to the millimetre.

Materials and options

Carpentry boards: four options and how to choose

The board drives the stability of the unit, the finish quality and the final price. We compare the four options commonly used in bespoke home carpentry.

park

Solid timber (oak, beech)

Best fit

Hardwood board in thicknesses that take moulding, planing and refurbishment. The choice for entrance doors, living-room furniture or pieces with a visible joint.

Worth knowing

A living material: it expands and contracts with ambient humidity. High price per m² and longer lead times. Design must allow for movement (rebates, clearances).

format_paint

Lacquered MDF

Best fit

MDF board (medium density) with primer and lacquer applied in workshop or on site. Delivers perfect finishes, exact colour and crisp edges. Common in passage doors and wardrobe fronts.

Worth knowing

Not suitable for areas with persistent moisture or edges exposed to continuous impact. Lacquer scratches with use; on-site touch-up leaves a visible mark unless the whole piece is repainted.

texture

Natural veneer

Best fit

Plywood or MDF core with a thin layer of natural wood (oak, walnut, ash). Delivers real-wood look and grain at a far lower price and weight than solid timber.

Worth knowing

The veneer is thin: it does not take deep-sanding refurbishment. Grain must be matched between pieces at manufacture time; once assembled it can no longer be corrected.

view_module

High-resistance melamine

Best fit

Chipboard with high-density melamine coating. Standard option for wardrobe interiors, shelving and non-visible areas.

Worth knowing

Edges must be covered with glued ABS edging: a badly closed edge lets moisture in and swells the board. It cannot be lacquered or refurbished, only replaced.

Before the workshop

Four variables we decide at measurement

A bespoke unit is built in the workshop but designed in the home. During the measuring visit we verify four variables that shape the project and the price.

straighten

Plumb and square

Measurements at several points of the opening with plumb line and square. An opening with 5 cm deviation needs a design that absorbs it (scribe strips or rebated sides).

layers

Board material

Solid timber, natural veneer, lacquered MDF or melamine depending on use and visibility. Decision driven by ambient humidity, expected load and intended finish.

home_repair_service

Hardware and runners

Concealed hinges with damping, drawer runners with declared load capacity and European-cylinder locks. Cheap hardware goes out of alignment in the first summer.

account_tree

Sequencing with other trades

In renovations: final measurement after plaster, paint and floor fitted — not before. A unit measured over works-in-progress comes out off.

Workflow

From measurement to fitting: how bespoke carpentry is executed

Bespoke carpentry combines workshop and on-site work. This is the typical sequence, with validation points where the client approves before moving to the next phase.

straighten
01
Measurement and project

Measurement with plumb line and square at several points of the opening, drawing of the real plan with wall deviations, and proposed interior layout validated by the client.
description
02
Cut list and materials

Cut list of pieces in workshop software, final choice of material, edging, lacquer or veneer and hardware. Delivery of final plan with image of the assembled unit.
construction
03
Workshop manufacture

CNC cutting of boards, ABS edging, sanding, priming and lacquering or veneering of the visible finish in controlled dust and humidity conditions.
home_repair_service
04
On-site fitting

Protected transport, on-site assembly with adjustment of side panels to the real deviation of the opening, hardware fitting and levelling with adjustable feet.
check_circle
05
Review and handover

Final adjustment of doors and drawers, regulation of damped hinges, cleaning and client walk-through of daily-use points before delivery.

Hardware and detail

The piece lasts as long as its hinges

Doors, drawers and sliding fronts are only as good as their hardware. Specifying the right hinge, runner and damper is what keeps the carpentry working after ten years of daily use.

check_circle Concealed hinges with built-in soft close
check_circle Full-extension drawer runners rated for 40 kg
check_circle Push-to-open on handleless fronts
check_circle Adjustable feet to level on uneven floors

In depth

Bespoke carpentry in Málaga: measurement, materials and quality hardware

Bespoke carpentry resolves everything an off-the-shelf product cannot cover: using every centimetre of the available opening, absorbing the deviations of old walls and delivering personalised finishes in finish, colour and interior layout. The difference between a bespoke unit and a standard one is in the millimetric measurement of the opening (plumb, square, levels) and in the hardware: a correct hinge lasts 15 years; a wrong one goes out of alignment in the first summer. For that reason the first visit is a measurement visit, not a sales visit.

The choice of board is the decision with the highest impact on cost and behaviour. Solid timber (oak, beech, treated pine) is the option for entrance doors, living-room furniture and pieces with visible joints; lacquered MDF delivers perfect finishes at a controlled cost, usual in passage doors and wardrobe fronts; natural veneer offers real-wood look at lower price and weight; high-resistance melamine is the standard for wardrobe interiors and non-visible areas. In bathrooms and kitchens we work with moisture-resistant boards and stainless-steel hardware to avoid rust and swelling in the long term.

A bespoke piece is built in the workshop but designed in the home. The measuring visit is key: measurements are taken at several points of the opening with plumb line and square to absorb wall deviations, and the piece is designed so the side panels can be adjusted on site to the real geometry of the opening. The workshop manufacture (CNC cutting, ABS edging, lacquer or veneer) is done in controlled dust and humidity conditions, and the on-site fitting ends with hinge regulation, drawer-runner adjustment and a client walk-through of daily-use points.

Related services